Is it possible to purchase only the caddy that pull out of the cabinet? I can't use the sliding shelf unit because my cabinet opening height is only 19 5/8 inches tall. View answer
Asked 2 ´years ago | Blind Corner Cabinet Organizers > Omega National Products KitchenMate Blind Corner Caddy with Swing-Out Motion Maple P0650MNL1
Is a 32" D-shaped lazy susan base slightly larger than a 32" full circle base? i.e. on a D-shape, does the 32" measure from the flat edge to the opposite side or is it still the overall diameter? I'm making a diagonal corner base cabinet and trying to decide between the D-shape and full circle. Unfortunately the video on measuring the cabinets for the lazy susan's doesn't go into that much detail. View answer
Asked 2 ´years ago | D-Shape Lazy Susans > Rev-A-Shelf 32" Wood D-Shape 1 Shelf Lazy Susan with Swivel Bearing Natural Maple LD-4BW-201-32SBS-1
I ordered the following --Blum 79B3598 110 Degree CLIP Top BLUMOTION Hinge, Soft-Close, +45 Degree Diagonal, Inserta. I need the same hinge but a screw-on. Please let me know the part number so I can order. View answer
Asked 2 ´years ago | Concealed European Cabinet Hinges > Blum 110 ° CLIP top BLUMOTION Overlay +45 ° II Soft-Closing Angled Hinge INSERTA Installation Nickel-Plated 79B3598
Can I cut off 7/8" off the back of each side. My space is only 11" deep. Is the rolled up tambour in the front or back of the overhead space? View answer
Asked 2 ´years ago | Appliance Garages and Tambour Door Kits > Omega National Products 24" Veneer Door Straight Appliance Garage Set Red Oak AG-100SVR-24
I like to use a square bit to screw these small screws in is this possible so does a square bit fit? View answer
Asked 2 ´years ago | Drawer Front Adjustment Screws > WE Preferred 1MMXP08100S2Z-4 (80330) Drawer Front Adjusting Screw, Mod Washer Head Phillips, Type 17 Auger Pt, Coarse, 1 x 8, Zinc, Bulk-1000
9 5/16" being the depth across the top lip for the 35 Quart PRWC what is the depth immediately below the lip. I need to place this inside a trash compactor. The inner width of the compactor is 8.25". Trying to see if this will fit inside the compactor bin. .The lip can rest on top of the bin ans the depth is not a concern. View answer
Asked 2 ´years ago | Replacement Bins & Accessories > 35 Quart White Replacement Waste Container Knape and Vogt QT35PB-WH
I want to flush mount these standards. I assume a router will work best. what is the routed width and depth? any rules how far those should be mounted from the front and back? 2 inches maybe? View answer
Asked 2 ´years ago | Pilasters and Clips > KV 255AL BR 24, 24in 255 Series Pilaster, Surface or Flush Mount, Brass Aluminum, Knape and Vogt
How is this installed, what are all of the dimensions?. What does it come with? 11" Wood Tray Divider Roll-Out with 3 Dividers Maple Omega National T3196MNL1 View answer
Asked 2 ´years ago | Base Cabinet Organizers > Omega National Products 5" Wood Tray Divider Roll-Out with One Divider Maple T3194MNL1
The long arm and fairly thin metal of the Salice C27YA99 Pie Corner hinge is causing 1/4" sag in my corner door. It is very flimsy and won't suffice with the weight of the door. Even adding a third hinge will not likely solve the issue. Is there a heavier sag resistant hinge that would work better for me? View answer
Asked 2 ´years ago | Pie-Cut Corner with Bi-Fold Center Door Hinges > Salice C27YA99, Pie Corner Hinge, Rapido
