Will the KV 8404 Face Frame Bracket work with the KV GSlide GS4200 series drawer slides? I don't see an equivalent part listed with them, but I need a face frame bracket for the slides I already own. View answer
Asked 5 ´years ago | Drawer Slide Accessories > KV 8404, Front Face Frame Bracket for Various Ball Bearing KV Drawer Slides, Zinc, Knape and Vogt
Can I use these for holding a speaker frame onto the front speaker baffle on some homemade speakers? There is very little weight load (it's a 6.5" woofer I am clamping from the front exterior). I inadvertently made the speaker hole a bit too large, leaving very small amount of material to use existing mount holes on the speaker. Speaker will be "glued" (more like sealed) with clear silicone all about the back, outside frame edge - think I can use these for permanent clamps? View answer
Asked 5 ´years ago | Mirror Clips > Mirror Clip for 1/4" Material Thickness Anodized Knape and Vogt 288 ANO
I recently purchased two of your Nexus 21 inch pie cut corner hinges and two of your Nexus 170-degree full overlay hinges. I was wondering which mounting plates I need for these hinges? View answer
Asked 5 ´years ago | Concealed European Cabinet Hinges > 170° Full Overlay Nexis Hinge Self-Close Screw-on Grass 138.765.73.0015
Which 1/4" overlay face frame concealed hinge offers the smallest gap between the door and cabinet when door is closed? Also, if the hole was previously drilled too far from the edge, how can it be widened to accommodate the 1/4" overlay? View answer
Asked 5 ´years ago | Concealed Compact Cabinet Hinges > Grass 04429A-15 TEC Soft-Close Hinge, Wrap Mount, 1/4 Overlay, Screw-on, 45mm Boring Pattern
Are you at liberty to divulge the Chinese manufacture of the KN95 masks. Not all KN95's are created equal, some are very good while others failed certification testing. Before purchasing I would like to know exactly what I'm buying. View answer
Asked 5 ´years ago | KN95 Disposable Mask White Bulk-10 Masks
Our drawer is 21” but the box is 23 from inside to inside. Would this be the 21” brackets? Want to make sure the bracket can reach from the back of the box to the front. View answer
Asked 5 ´years ago | Undermount Drawer Slides > PRO 500 21" Economy Full Extension Soft-Close Undermount Drawer Slide 6/Box WE Preferred
I was advised by Blum that this hinge might work for my needs. I have narrow stiles in one area of my kitchen. The cabinets do have a face frame and there is a 3/4 overlay. Their brochure doesnt go up to a 3/4 overlay but the 0 hinge plate comes close. Would this hinge and the 0 hinge plate work for me? If so what is the part number for that hinge plate and I will place an order. View answer
Asked 5 ´years ago | Specialty Application Hinges > Blum 94 Degree CLIP Top Mini Hinge Self-Close Full Overlay Screw-on Blum 71T0550
Hi - Thanks but it's the "depth" listed above, the 9 5/16" measurement that I need to know what it tapers down to at the bottom. Not lengthwise end-to-end, BUT ACROSS the bottom side-to-side! Thanks!! View answer
Asked 4 ´years ago | Trash Pull-Outs: Replacement Pull-Out Bins and Accessories > 35 Quart White Replacement Waste Container Knape and Vogt QT35PB-WH
Hi, I need to know if the BOTTOM ["depth" in description] is same as the TOP. I would call this the WIDTH. But whatever. :) It's the 9 5/16" measurement listed above. And if smaller -- what is the exact measurement across the bottom? THANKS!! View answers
Asked 4 ´years ago | Trash Pull-Outs: Replacement Pull-Out Bins and Accessories > 35 Quart White Replacement Waste Container Knape and Vogt QT35PB-WH
Are they clear Anodized View answer
Asked 4 ´years ago | Cabinet Handles & Pulls > Paramount Extrusions 5090 Aluminum 6' Pull
Is there a compatible model that has soft/self close? Are there just compatible soft/self close drawer slides available that could be used to upgrade an existing unit? View answer
Asked 4 ´years ago | Top Mount Trash Pull-Outs > Rev-A-Shelf 4WCTM Top Mount Double 35 Quart Waste Container Maple Rev-A-Shelf 4WCTM-18DM2-162
