What is the minimum width of cabinet to hold this caddy. My blind corner-to-be has an 8' timber post in it. Do you have a video for this? What is the recommended door width - not the minimum? View answer
Answer posted 3 years ago | Blind Corner Cabinet Organizers > KitchenMate Blind Corner Caddy with Swing-Out Motion Maple Omega National P0650MNL1
Hi, I have two bookcases, each approximately 12' long and 8 feet high. I would like to use 4 x 8 sheets of 1/4" acrylic for doors. Will this work with this track? Thanks Kevin View answer
Answer posted 3 years ago | Sliding Door Track Assemblies > 48" Roll-Ezy Track Sliding Glass Door Hardware Set for By-Passing 1/4" Glass Doors Knape and Vogt P992 ZC 48
How big are the screws? View answer
Answer posted 3 years ago | METABOX File Drawer Application - Metafile > Blum METAFILE Hanging Rail Support Bracket Blum ZRM.0005
what is max overlay of this item? Thanks View answer
Answer posted 3 years ago | Salice Wind Lift Mechanisms > Salice FRAKFEXSSN9 "S" Wind Lift System, Soft-Closing
I read a review about the Rev-A-Shelf 53WC-2150SCDM-213 or 4WCBM-18DM-2 that said the opening mechanism pushes the trash shelf out all the way, as if you cannot just open it part way. Could you tell me if that is correct with these 2 models? I didn't see any other comments about that. I'd like to know before buying one. Normally a soft close door/drawer is just opened normally as far as you want and then it does a soft close. Thank you! View answer
Answer posted 3 years ago | Bottom Mount Trash Pull-Outs > Rev-A-Shelf 53WC Double 50 Quart Bottom Mount Waste Container Orion Gray Rev-A-Shelf 53WC-2150SCDM-213
Your website shows RH and LH units for the Cornerstone Max Pull Out unit. Vauth-Sagel's website says it can be installed in either hand. What is correct? View answer
Answer posted 3 years ago | Blind Corner Cabinet Organizers > CORNERSTONE MAXX Scalea Blind Corner Pull-Out LH for 18" Opening Carbon Steel Gray/Maple Vauth-Sagel
In the product description it says the Rear Brackets for the 27 inch 569A are optional. It says to look for it in Related Products, but there doesn't seem to be a listing for the rear brackets in related products. Could you provide the link to the rear bracket compatible with this slide? View answer
Answer posted 3 years ago | Blum 27" TANDEM plus BLUMOTION 569A Undermount Heavy Duty Full Extension Drawer Slide Blum 569A6860B
Since Blum is impossible to get, can I use the same size drawer boxes for these slides? We typically subtract 3/8 total form ID of the cabinet. View answer
Answer posted 3 years ago | Undermount Drawer Slides > Dynapro 16 2-D 18" Full Extension Soft-Close Undermount Drawer Slide for 5/8" Drawer Grass F130100736204
Where is this product made View answer
Answer posted 3 years ago | Cabinet Handles & Pulls > Wire Pull 96mm Center to Center Natural Aluminum WE Preferred A271-96ANO
Where is this product made View answer
Answer posted 3 years ago | Workstation Brackets > A & M Hardware, 12"x18" Workstation Bracket, 12"x18" Primed, Packed 1 Pair
Can it be used on plastic surface View answer
Answer posted 3 years ago | Laminate Repairer > SeamFil Laminate Repairer Black 1.0 oz Tube Kampel 914
Where is this product made? View answer
Answer posted 3 years ago | Salice 45° Specialty Hinge Self-Closing Screw-On Salice C2JBM99AC
Salice D2vx09 fits Salice D0SHSNG? Thanks View answer
Answer posted 3 years ago | Soft-Close Adapters > Salice D0SHSNG, Euro Smove Soft Close Piston, Light Tension
