Hello, I'm looking to pair a hinge and mounting plate systew on face frame inset doors. I need to raise the mounting plate to approx. - 27mm to 30mm to lift the hinge to nearly flush with the faceframe edge (just like a frameless). I noted a few Salice BAR options to accomplish this however, a matching screwed on hinge has too many options to narrow down. Please help! Thank you! View answer
Asked 1 ´year ago | Hinge Mounting Plates > Salice 30mm Wing Hinge Mounting Plate Screw-On Salice BAR3RM9
Where do I find the pricing for 107" ladder? I only find 92" on Woodworker Express website. View answer
Asked 1 ´year ago | Rolling Library Ladder Components > E-Glide Satin Nickel Sliding Hook Ladder 12' Hardware Kit with 92" Prefinished Maple Ladder Customer Service Hardware EG.300-92MA-12.02-PF
I want to buy eight Sugatsune H160-C34-18 hinges. The product detail page (https://www.woodworkerexpress.com/h160-series-european-thick-door-hinge-18mm-overlay-self-closing-sugatsune-h160-c34-18.html) has the tip "Hinge plates and screws sold separately. See Related Products below", but there are no hinge plates included in the Related Products section, and searching your site for "mounting plate H160-C34" as well as for "hinge plate H160-C34", and I can't find the hinge plate for that hinge. Can you please help me find it? View answer
Asked 1 ´year ago | Concealed European Cabinet Hinges > H160 Series European Thick Door Hinge 18mm Overlay Self-Closing Sugatsune H160-C34-18
Can the polybak sheet be cut into smaller pieces before shipping? For example, can the 49x97 sheet be cut into 16 1x2 sections before shipping? If not, is it shipped rolled? View answer
Asked 1 ´year ago | Backers > Polybak PB69 Veneer Backer/Balancer .020" Thick Richwood Industries PBS69BR28-4X8
can the 7555/533 be used to replace a 7557/533 without having to drill new holes. Do both of them have the holes in the same locations?I want to switch to a soft-close system View answer
Asked 1 ´year ago | Undermount Drawer Slides > Salice 21" Futura Full Extension Soft-Close Undermount Drawer Slide Salice A7555/533 CP6
Will these waste containers (35 Quart Champagne Replacement Waste Container Rev-A-Shelf RV-35-12-52)? I purchased them and they don't fit in the bottom mount waste container I have. View answer
Asked 1 ´year ago | Bottom Mount Trash Pull-Outs > Double 35 Quart Bottom Mount Waste Container with Soft Close and Wood Carriage WE Preferred SZWWB235WH
Is it possible to purchase only the caddy that pull out of the cabinet? I can't use the sliding shelf unit because my cabinet opening height is only 19 5/8 inches tall. View answer
Asked 1 ´year ago | Blind Corner Cabinet Organizers > KitchenMate Blind Corner Caddy with Swing-Out Motion Maple Omega National P0650MNL1
Is a 32" D-shaped lazy susan base slightly larger than a 32" full circle base? i.e. on a D-shape, does the 32" measure from the flat edge to the opposite side or is it still the overall diameter? I'm making a diagonal corner base cabinet and trying to decide between the D-shape and full circle. Unfortunately the video on measuring the cabinets for the lazy susan's doesn't go into that much detail. View answer
Asked 1 ´year ago | D-Shape Lazy Susans > Rev-A-Shelf 32" Wood D-Shape 1 Shelf Lazy Susan with Swivel Bearing Natural Maple Rev-A-Shelf LD-4BW-201-32SBS-1
I ordered the following --Blum 79B3598 110 Degree CLIP Top BLUMOTION Hinge, Soft-Close, +45 Degree Diagonal, Inserta. I need the same hinge but a screw-on. Please let me know the part number so I can order. View answer
Asked 1 ´year ago | Concealed European Cabinet Hinges > Blum 110 Degree CLIP Top BLUMOTION Hinge Soft-Close +45 Degree Diagonal Inserta Blum 79B3598
Can I cut off 7/8" off the back of each side. My space is only 11" deep. Is the rolled up tambour in the front or back of the overhead space? View answer
Asked 1 ´year ago | Appliance Garages and Tambour Door Kits > Omega National AG-100SVR-24, 24 W Appliance Garage Set - Straight Unit, Red Oak Veneer Door