Will the KV 8404 Face Frame Bracket work with the KV GSlide GS4200 series drawer slides? I don't see an equivalent part listed with them, but I need a face frame bracket for the slides I already own. View answer
Asked 5 ´years ago | Drawer Slide Accessories > KV 8404, Front Face Frame Bracket for Various Ball Bearing KV Drawer Slides, Zinc, Knape and Vogt
Can I use these for holding a speaker frame onto the front speaker baffle on some homemade speakers? There is very little weight load (it's a 6.5" woofer I am clamping from the front exterior). I inadvertently made the speaker hole a bit too large, leaving very small amount of material to use existing mount holes on the speaker. Speaker will be "glued" (more like sealed) with clear silicone all about the back, outside frame edge - think I can use these for permanent clamps? View answer
Asked 5 ´years ago | Mirror Clips > Mirror Clip for 1/4" Material Thickness Anodized Knape and Vogt 288 ANO
I recently purchased two of your Nexus 21 inch pie cut corner hinges and two of your Nexus 170-degree full overlay hinges. I was wondering which mounting plates I need for these hinges? View answer
Asked 5 ´years ago | Concealed European Cabinet Hinges > 170° Full Overlay Nexis Hinge Self-Close Screw-on Grass 138.765.73.0015
Which 1/4" overlay face frame concealed hinge offers the smallest gap between the door and cabinet when door is closed? Also, if the hole was previously drilled too far from the edge, how can it be widened to accommodate the 1/4" overlay? View answer
Asked 5 ´years ago | Concealed Compact Cabinet Hinges > Grass 04429A-15 TEC Soft-Close Hinge, Wrap Mount, 1/4 Overlay, Screw-on, 45mm Boring Pattern
Are you at liberty to divulge the Chinese manufacture of the KN95 masks. Not all KN95's are created equal, some are very good while others failed certification testing. Before purchasing I would like to know exactly what I'm buying. View answer
Asked 5 ´years ago | KN95 Disposable Mask White Bulk-10 Masks
I was advised by Blum that this hinge might work for my needs. I have narrow stiles in one area of my kitchen. The cabinets do have a face frame and there is a 3/4 overlay. Their brochure doesnt go up to a 3/4 overlay but the 0 hinge plate comes close. Would this hinge and the 0 hinge plate work for me? If so what is the part number for that hinge plate and I will place an order. View answer
Asked 5 ´years ago | Specialty Application Hinges > Blum 94 Degree CLIP Top Mini Hinge Self-Close Full Overlay Screw-on Blum 71T0550
what is the temp range? is it in Fahrenheit? View answer
Asked 5 ´years ago | First Aid > Dual Mode Digital Thermometer
TEC hinges 02824-a15 will not fully close my 23" and 19" base cab doors. Tried every position on the soft close tension adjustment to no avail. Any suggestions? View answer
Asked 5 ´years ago | Concealed Compact Cabinet Hinges > Grass 02824A-15 TEC Adjustable Soft-close Hinge, Wrap Mount, 1/2 Overlay, Dowel, 42mm Boring Pattern
I have 18inch wide cabinet openings. Can I use the 15" or 18" version of the pullout? I think I would prefer using the 15" version just to avoid fit issues. View answer
Asked 5 ´years ago | Bottom Mount Trash Pull-Outs > Rev-A-Shelf 4WCSC Double 35 Quart Bottom Mount Waste Container Maple Rev-A-Shelf 4WCSC-2135DM-2
You show two different specs for this product. One near the top right under the stars and one in the Product Details. Which one is correct? View answer
Asked 5 ´years ago | Trash Pull-Outs: Replacement Pull-Out Bins and Accessories > 27 Quart White Replacement Waste Container Knape and Vogt QT27PB-W
The instructions for model Omega National 48" Wide Signature Deluxe Wall Hood with Liner for Broan, Red Oak, R2548SMB1OUF1 states that the included liner will also work with Broan in-line blower 1100 CFM. Would that also work with a Jenn-Air 1200 CFM Dual High Performance Blower? View answer
Asked 6 ´years ago | Signature Deluxe Arched 48" Wide Wall Hood with Broan Liner Red Oak Omega National R2548SMB1OUF1
I want to purchase 40 of these locks and would like to verify a masterkey comes with them that will fit all locks? View answer
Asked 6 ´years ago | Disc Tumbler Cam Locks > CompX C8053-MKKD-14A Cam Lock, 90° Cam Turn, Flush or Lipped/Overlay, Cylinder 1-3/16, Max 7/8, Keyed Different & Masterkeyed, Bright Nickel
