Lid Supports and Stays Q&A

Question 1

What is opening angle and does it include diagram instructions View answer

Asked 24 ´days ago | Lid Supports and Stays > Delta Lift-Up or Drop-Down Lid Mechanism PMI 810.100.060

Question 2

To use the Sugatsune left hand adjustable soft down stay in a toy box do you need one on each side (a right and left) or just one? View answer

Asked 7 ´years ago | Lid Supports and Stays > Adjustable Soft-Down Stay for Top Opening Door RH Nickel Sugatsune NSDX-20RK

Question 3

If cabinet pulls to the right, do you need a left hand pull or a right hand pull? View answer

Asked 7 ´years ago | Lid Supports and Stays > Adjustable Soft-Down Stay for Upward Opening Door LH Nickel Sugatsune NSDX-35LK

Question 4

Can you provide mounting instructions for SKU 7232? Thanks Fran View answer

Asked 7 ´years ago | Lid Supports and Stays > KV 472 ANO 6, 6in Lid Support, Anochrome, Knape and Vogt

Question 5

I am needing something to keep a toy box lid locked in open position, so my son can't close it. I also need it so that I can close it when needed. Do you think this piece will work. View answer

Asked 6 ´years ago | Lid Supports and Stays > Delta Lift-Up or Drop-Down Lid Mechanism PMI 810.100.060

Question 6

for a 28" (w) x 13" (tall) horizontally mounted cabinet door with two hinges at the top, do you need a stay on each side of the door or will a single stay on one side be adequate to hold the door open? View answer

Asked 6 ´years ago | Lid Supports and Stays > Adjustable Soft-Down Stay for Upward Opening Door LH Nickel Sugatsune NSDX-35LK

Question 7

Does this stay open on a piston too or just close? I need something for a drop down that opens softly View answer

Asked 5 ´years ago | Lid Supports and Stays > SDS Top-Opening Flap Door Stay Grey Sugatsune SDS-C301N/G

Question 8

Does the right hand lid fitting mount on the right side facing the cabinet? View answer

Asked 5 ´years ago | Lid Supports and Stays > Hettich 1001144, 20lb Left Hand Lid Fitting, Zinc

Question 9

there is no instruction sheet for installation View answer

Asked 5 ´years ago | Lid Supports and Stays > Soft Down Flap Stay for Upward Opening Cabinet White Sugatsune SDS-C301N/WHT

Question 10

Where is the table showing the weight ratings? View answer

Asked 5 ´years ago | Lid Supports and Stays > Heavy-Duty Soft-Close Lid Stay for Upward Opening Door LH Light Gray Sugatsune SLS-ELAN-HL

Question 11

The builder of my chest used two Carlson Capitol 703LH hinges. I need to replace them. will a 703RH hole pattern line up? View answer

Asked 4 ´years ago | Lid Supports and Stays > Carlson Capitol 703-GREEN, Lid Support, 40-45ft lb

Question 12

what is the color of the Carlson Capitol 702RH-YELLOW, Right Hand Lid Support, 65-95ft lb? View answer

Asked 3 ´years ago | Lid Supports and Stays > Carlson Capitol 703-YELLOW, Lid Support, 65-95ft lb

Question 13

Do you have a vertical lift solution for smaller door? 15x16" 2-3 lbs. View answer

Asked 3 ´years ago | Lid Supports and Stays > Vertical Swing Lift Up Mechanism for Door Weight 5.5 to 7.7 lb Sugatsune SLUN-3

Question 14

Does this include Arm Mounting Plate & Arm Mounting Screws View answer

Asked 2 ´years ago | Lid Supports and Stays > Adjustable Soft-Down Stay for Top Opening Door LH Nickel Sugatsune NSDX-20LK

Question 15

Can the vertical lift hinge be applied to an inset door type (18.25" tall x 33" wide)? View answer

Asked 2 ´years ago | Lid Supports and Stays > Vertical Swing Lift Up Mechanism for Door Weight 5.5 to 7.7 lb Sugatsune SLUN-3

Question 16

Is this soft close? View answer

Asked 2 ´years ago | Lid Supports and Stays > WE Preferred H02-CH00S034 - Chest Hinge

Question 17

Can this be installed on a door that is 42” wide? View answer

Asked 2 ´years ago | Lid Supports and Stays > Vertical Swing Lift Up Mechanism for Door Weight 5.5 to 7.7 lb Sugatsune SLUN-3

Question 18

The torque ranges don't make since. I have one bench lid that is 80 kg·cm and another that is 115 kg·cm. Will the light duty seat stay be too much for these lids? View answer

Asked 1 ´year ago | Lid Supports and Stays > HDS Soft-Down Stay Light-Duty LH White Sugatsune HDS-30KL/WHT

Question 19

Can these stays be used for a drop-down desk installation? I understand that the torque moment calculations are to coordinate the panel weight with the soft-down mechanism, but what are the absolute weight maximums? Once open, I presume the stay acts to support additional weight (as it would for a desk with items placed on the desk surface), but I don't see that spec anywhere. Thanks, Oliver H. View answer

Asked 1 ´year ago | Lid Supports and Stays > Heavy-Duty Soft-Down Stay RH White Sugatsune HDS-10HR/WHT

Question 20

Will any of these fit into a 6inch opening? I would like to make a pull-down draw and only have 6inches inside the cabinet View answer

Asked 1 ´year ago | Lid Supports and Stays > Delta Lift-Up or Drop-Down Lid Mechanism PMI 810.100.060

Question 21

I need a hinge for a laundry chute door but only want the door to open to about 45 degrees. Can this hinge only open to 45 degrees and not 90 degrees? Thanks View answer

Asked 1 ´year ago | Lid Supports and Stays > Adjustable Soft-Down Stay for Downward Opening Door LH Nickel Sugatsune NSDX-10LK

Question 22

For a wall hung entertainment center with inset doors - down swinging. Looking for a small gas stay to support door? What are the blum hinges for inset and mounting plates? Thanks Jim View answer

Asked 11 ´months ago | Lid Supports and Stays > Adjustable Soft-Down Stay for Downward Opening Door LH Nickel Sugatsune NSDX-10LK

Lid Supports and Stays Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic