I see all this: for a 3/4" door; Hardware set includes: matching (1) piece of upper guide and (1) piece of lower track; Upper Size: 1-15/16 W x 13/16 H x 48 L; However: need to know for sure, HOW WIDE IS THE BOTTOM TRACK (not stating that it is the same width as the upper track)? And I need to make sure the middle section separating the 2 doors is not very thick but rather hoping very thin, and same with outside edges of track. I have very limited space to place the track in. View answer
Answer posted 1 year ago | Sliding Door Track Assemblies > 3/4" Door Assembly Kit 48" Tan Knape and Vogt P2419 TAN 48
How many are needed per 27” slide? View answer
Answer posted 1 year ago | Drawer Slide Accessories > Blum Tandem Side Spacer Blum T59.3570
Hello, do you have to use one of the Broan vents shown on your site? Would you be able to use a ductless vent that has buttons on the front? View answer
Answer posted 1 year ago | Wall Mount Range Hoods > Omega National Products Classic Series 30" Wide Wall Mount Range Hood with Broan Liner Hickory R70302SMB1HUF1
Picture shows hinge WITH a hinge plate. Description says it doesn't come with the hinge plate, but there's no link or hinge plate available. So Does it come with hinge plate, like the picture shows and if it doesn't, do you sell them?? View answer
Answer posted 1 year ago | Pie-Cut Corner with Bi-Fold Center Door Hinges > Grass America Nexis 21 Pie-Cut Hinge Screw-on 146.700.01.0015
Received the 1-1/8" snap in magnetic catch #555-P. Does it come in a size that is not as deep? This is for a vintage metal kitchen cabinet. The size fits in the location but is a little bit too deep. One a little less deep than the 13/16 would work better. Help View answer
Answer posted 1 year ago | Catches and Latches > 1-1/8" Snap in Magnetic Catch with Screws and Strike Aluminum Epco 555-P
I have a 2-drawer Levenger file cabinet that is 20 years old and still looks brand new. The problem I am having is with the SN-400 anti-tip mechanism on the left-hand side of each drawer. The bottom one sticks and will not let me open the drawer. I have removed both of the SN-400 mechanisms, temporarily, to be able to use the cabinet but would like to replace them. Do you have a mechanism available that is an upgrade to the SN-400 that I could purchase instead? Any assistance would be greatly appreciated. View answer
Answer posted 1 year ago | Lock Accessories > CompX Timberline SN-400 Timberline Lock, Gang Lock Accessories, Anti-Tip Interlock System, Anti-Tip Snapper
Hi. Can you tell me what the significance is of the last characters in the model number on these slides? I've seen some that have '-01B' and others that have '-02B' as the last characters. Thanks View answer
Answer posted 1 year ago | Undermount Drawer Slides > Blum 21" TANDEM plus BLUMOTION 563H Soft-Close Undermount Drawer Slide for 1/2" - 5/8" Drawer Side Blum 563H5330B
I am upgrading my slides from existing plastic runner and wheel system. I have a face frame and overlay drawer front. What is the minimum clearance between the outer edge of the drawer and the face frame. I have 9/16" on either side. Also, my drawer is 21" front to back outside not including the face. The distance from the inside of the face frame to the rear of the cabinet where I will use rear mount brackets is about 23". Are these slides long enough? View answer
Answer posted 1 year ago | Undermount Drawer Slides > Blum 21" TANDEM plus BLUMOTION 563F Undermount Drawer Slide Blum 563F5330B
