Can someone tell me what the 11 13/16" measurement is referring to? Also, Double Type vs. Single Type. Trying to compare this mechanism vs. Soft-Close Mechanism-Inset 12-3/8" Single Type Sugatsune IF-102S-16 . Thank you! View answers
Asked 1 ´year ago | Soft-Close Mechanism-Inset 11-13/16" Double Type Sugatsune IF-102W-14
I want to buy eight Sugatsune H160-C34-18 hinges. The product detail page (https://www.woodworkerexpress.com/h160-series-european-thick-door-hinge-18mm-overlay-self-closing-sugatsune-h160-c34-18.html) has the tip "Hinge plates and screws sold separately. See Related Products below", but there are no hinge plates included in the Related Products section, and searching your site for "mounting plate H160-C34" as well as for "hinge plate H160-C34", and I can't find the hinge plate for that hinge. Can you please help me find it? View answer
Asked 1 ´year ago | Concealed European Cabinet Hinges > H160 Series European Thick Door Hinge 18mm Overlay Self-Closing Sugatsune H160-C34-18
can the 7555/533 be used to replace a 7557/533 without having to drill new holes. Do both of them have the holes in the same locations?I want to switch to a soft-close system View answer
Asked 1 ´year ago | Undermount Drawer Slides > Salice 21" Futura Full Extension Soft-Close Undermount Drawer Slide Salice A7555/533 CP6
Will these waste containers (35 Quart Champagne Replacement Waste Container Rev-A-Shelf RV-35-12-52)? I purchased them and they don't fit in the bottom mount waste container I have. View answer
Asked 1 ´year ago | Bottom Mount Trash Pull-Outs > Double 35 Quart Bottom Mount Waste Container with Soft Close and Wood Carriage WE Preferred SZWWB235WH
Is a 32" D-shaped lazy susan base slightly larger than a 32" full circle base? i.e. on a D-shape, does the 32" measure from the flat edge to the opposite side or is it still the overall diameter? I'm making a diagonal corner base cabinet and trying to decide between the D-shape and full circle. Unfortunately the video on measuring the cabinets for the lazy susan's doesn't go into that much detail. View answer
Asked 1 ´year ago | D-Shape Lazy Susans > Rev-A-Shelf 32" Wood D-Shape 1 Shelf Lazy Susan with Swivel Bearing Natural Maple Rev-A-Shelf LD-4BW-201-32SBS-1
Can I cut off 7/8" off the back of each side. My space is only 11" deep. Is the rolled up tambour in the front or back of the overhead space? View answer
Asked 1 ´year ago | Appliance Garages and Tambour Door Kits > Omega National AG-100SVR-24, 24 W Appliance Garage Set - Straight Unit, Red Oak Veneer Door
9 5/16" being the depth across the top lip for the 35 Quart PRWC what is the depth immediately below the lip. I need to place this inside a trash compactor. The inner width of the compactor is 8.25". Trying to see if this will fit inside the compactor bin. .The lip can rest on top of the bin ans the depth is not a concern. View answer
Asked 1 ´year ago | Trash Pull-Outs: Replacement Pull-Out Bins and Accessories > 35 Quart White Replacement Waste Container Knape and Vogt QT35PB-WH
I like to use a square bit to screw these small screws in is this possible so does a square bit fit? View answer
Asked 1 ´year ago | Drawer Front Adjustment Screws > WE Preferred 1MMXP08100S2Z-4 (80330) Drawer Front Adjusting Screw, Mod Washer Head Phillips, Type 17 Auger Pt, Coarse, 1 x 8, Zinc, Bulk-1000
